產品特點 施工簡單，高耐磨性，品質穩定，
技術參數 1、外 觀：粘稠液體，20000－60000cps/25℃。
2、絲 網：300－400目網版，絲印刮刀：70－75度聚氨酯刮刀。
3、輔助劑：稀釋劑C-2 UV專用開油水,固化劑S-8。
4、干固條件：烘烤15-30分鐘，或過流水拉后直接UV固化（能量要求800mj/cm2）。
5、用 量：35－40m2/Kg。
6、儲存方法：本品應儲存于避光容器內，避免受熱和潮濕，儲存期為半年，半年后性能若無變化可繼續使用。
7、包裝規格：1Kg/桶
施工程序 A、UV面/真空電鍍UV面/PU面
  1、按照油墨：固化劑＝10：1（重量比）加入S-8固化劑并攪拌均勻。
  2、根據施工粘度要求加入適量稀釋劑。
  3、印制完成后直接過流水線。
  4、UV固化（能量要求大于800-1200mj/cm2，EHT能量計）。
B、ABS/PC+ABS /PC/PMMA/HIPS等
  1、根據施工粘度要求加入適量稀釋劑。
  2、印制完成后普通烤爐75℃烘烤15-30分鐘。
  3、UV固化（能量要求大于800-1200mj/cm2，EHT能量計）。 
注意事項 1、使用前，應檢查油墨是否與基材適應，基材表面處理程度，基材表面干凈程度（是否有太多脫膜劑、離型劑、油漬），基材的柔韌性和剛性。
2、可用酒精擦拭去除灰塵、油漬、脫除脫膜劑和離型劑。
3、應試印確認后方可批量生產。
The features of the product are simple, high wear resistance and stable quality.
The technical parameters 1, appearance: viscous liquid, 2000060000cps/25 C.
2, screen: 300-400 mesh screen, silk screen scraper: 70-75 degree polyurethane scraper.
3, auxiliary agent: diluent C-2 UV special open oil, curing agent S-8.
4, dry solid conditions: baking for 15-30 minutes, or after running water to pull the direct UV curing (energy requirements 800mj/cm2).
5, dosage: 3540m2/Kg.
6, storage method: This product should be stored in the light avoidance container, avoid heat and humidity, the storage period of half a year, half a year after the performance if no change can continue to use.
7, package specification: 1Kg/ barrel
Construction procedure A, UV surface / vacuum electroplating UV surface /PU surface
1, according to the ink: the curing agent = 10:1 (weight ratio) added S-8 curing agent and stirred evenly.
2. Add appropriate diluent according to the requirement of construction viscosity.
3. After the printing is completed, the production line is directly over.
4, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
B, ABS/PC+ABS /PC/PMMA/HIPS, etc.
1. Add appropriate diluent according to the requirement of construction viscosity.
2. Bake for 15-30 minutes at 75 C after the printing and completion of the oven.
3, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
Precautions 1, before use, check whether the ink is compatible with the substrate, the degree of substrate surface treatment, the cleanliness of the substrate surface (whether there are too many film removal agents, release agents, oil stains), the flexibility and rigidity of the substrate.
2, using alcohol wiping to remove dust, oil stains, removal of film and deionization agent.[本信息來自于今日推薦網]